Visited the local Ikea today for breakfast, and on the way out i passed the "leftover corner"
After some searching i found this plank that had the same thickness as the rest, its black laminated, and it was cheap
![:wink:](http://www.dragonslairfans.com/smfor/Smileys/default/icon_wink.gif)
This will make the perfect topcover that i still need..
![](http://www.opdenkelder.com/pics/minipong/122.jpg)
Nice weather today, so i started with the last sanding portion..
![](http://www.opdenkelder.com/pics/minipong/123.jpg)
Then i sawed the fresh plank to the measurements that i need..
![](http://www.opdenkelder.com/pics/minipong/124.jpg)
Then i measured my leftover and it was enough to build the backdoor and the monitor support from..
![Roll Eyes ::)](http://www.dragonslairfans.com/smfor/Smileys/default/rolleyes.gif)
So i decided to ditch the door and support that i made last time.
Backdoor in place.. fits like a glove
![Cheesy :D](http://www.dragonslairfans.com/smfor/Smileys/default/cheesy.gif)
![](http://www.opdenkelder.com/pics/minipong/125.jpg)
"Roof" in place..
![Tongue :P](http://www.dragonslairfans.com/smfor/Smileys/default/tongue.gif)
![](http://www.opdenkelder.com/pics/minipong/126.jpg)
And from another angle..
![](http://www.opdenkelder.com/pics/minipong/127.jpg)
Last leftover cut to size, ready to cut a monitor hole in there
![](http://www.opdenkelder.com/pics/minipong/128.jpg)
Same procedure as the window in the cabinet, first 4 holes..
![](http://www.opdenkelder.com/pics/minipong/129.jpg)
And then saw the inner part out..
![Cool 8)](http://www.dragonslairfans.com/smfor/Smileys/default/cool.gif)
![](http://www.opdenkelder.com/pics/minipong/130.jpg)
It fits, but there is a bit too much space around, so i only use the normal screws in the bottom..
![](http://www.opdenkelder.com/pics/minipong/131.jpg)
for the top, i cannot screw in the tiny bit that i have in that corner..
Time to be creative again..
![Roll Eyes ::)](http://www.dragonslairfans.com/smfor/Smileys/default/rolleyes.gif)
Take 2 of those old electric pipe clamps..
![](http://www.opdenkelder.com/pics/minipong/132.jpg)
Hammer them flat, and spray paint them again..
The can go diagonal over the "topeyes" from the monitor..
![](http://www.opdenkelder.com/pics/minipong/133.jpg)
Now thats finished, time to put the panel in position and create some supports..
![](http://www.opdenkelder.com/pics/minipong/134.jpg)
![](http://www.opdenkelder.com/pics/minipong/135.jpg)
After measuring, i took out the protective foil..
Did i say shiny ?
![Grin ;D](http://www.dragonslairfans.com/smfor/Smileys/default/grin.gif)
![](http://www.opdenkelder.com/pics/minipong/136.jpg)
Some supports glued in place..
![](http://www.opdenkelder.com/pics/minipong/137.jpg)
And again Drying time..
![Angry >:(](http://www.dragonslairfans.com/smfor/Smileys/default/angry.gif)
![](http://www.opdenkelder.com/pics/minipong/138.jpg)
While drying, i finished the edges of the "Roof"
Lets see, "iron on strip"
Oh Wifeyyyyy, i need your Iron
![Grin ;D](http://www.dragonslairfans.com/smfor/Smileys/default/grin.gif)
![](http://www.opdenkelder.com/pics/minipong/139.jpg)
One side done, time to cut off the leftovers with a special tool..
![](http://www.opdenkelder.com/pics/minipong/140.jpg)
I need to say that after some practicing, it works really well..
![](http://www.opdenkelder.com/pics/minipong/141.jpg)
And the roof is finished..
![Cool 8)](http://www.dragonslairfans.com/smfor/Smileys/default/cool.gif)
![](http://www.opdenkelder.com/pics/minipong/142.jpg)
I will leave the protective foil on there untill the end.
Plenty of time when its finished to remove this foil..
I think that i got all the construction work done now,
May be a little detail sanding, but thats it..
Oh and i need to drill still the backdoor lock, but will do that after the monitor is in..
i dont want that i break the neck when i have the lock also in the center..
so will measure the space first and then find out how to make the door lock
![arrow :arrow:](http://www.dragonslairfans.com/smfor/Smileys/default/icon_arrow.gif)